ITW METHACRYLATES ITW PLEXUS, manufacturers of PLEXUS Methacrylate Adhesives, reports that the methacrylate technology of today represents "a quantum leap over the past performance of the more traditional acrylic technology" and was developed to fill the shortcomings such as the brittleness, gap filling and less than reliable cures of the early acrylics

The PLEXUS structural methacrylate adhesives provide superior performance across a wide range of substrates including  today's most advanced, difficult to bond plastics. EASY TO MIX AND APPLY: Plexus two component adhesives are combined in a ratio of 1:1, allowing them to be mixed and  dispensed using manual or less sophisticated non-metered dispensing equipment. WIDE RANGE OF SUBSTRATES...Methacrylate adhesives is compatible with a wide range of substrates including: Stainless Steel, Epoxy Coated Surfaces, PVC, ABS, Aluminum,Styrenecs, Steel, Noryl, Azloy, Rynite, Valox, Lomod, RIM Urethane, SMC, Xenoy, Bexloy, Ceramics and Ferrites.

	PLEXUS Methacrylate Structural Adhesives Technical Data A Product Line of ITW Adhesives

CLIP PACKS, CARTRIDGES, PAILS or DRUMS.

	Methacrylates Advancing Technolgy Dexter's most rapid growing product line is methacrylates- structural adhesives formulated specially for the most demanding high stress bonding applications. Here is just a short list of the advantages that are yours with Hysol methacrylates
	Minimal surface preparation
	Bond diverse substrates
	Fast cure times at room temperature
	Superior shear and peel strength
	Bondlines from 5 mils to 1 inch
	Minimal print-through on thin llaminates
	Unmatched environmental and chemical resistance

Hysol Methacrylate Adhesive Technical Data

Color	Tan	Yellow	Pale Yellow	Pale Yellow or Black	Pale Yellow	Light Yellow	Pale yellow	Light Yellow
Mix Ratio	1:1	1:1	10:1	10:1	10:1	10:1	10:1	10:1
Viscosity of Components	PartA 90,000 Part B 70,000	Part A 145,000 Part B 80,000	Part A 90,000 Part B 170,000	Part A 90,000 Part B 140,000	Part A 90,000 Part B 40,000	Part A 150,000 Part B 40,000	Part A 35,000 Part B 40,000	Part A 60,000 Part B 50,000
Gap Fill Inches	.005- .375	.005- .375	.005- .500	.005- .375	.005- .375	.005- .375	.005- .025	.005- 1.00
Open Time Minutes	4 - 6	4 - 6	7 - 10	2 - 4	4 - 6	4 - 6	4 - 6	20 - 25
Fixture Time (Minutes)	15 - 20	10 - 15	15 - 20	7 - 8	15 - 20	15 - 20	15 - 20	45 - 55
Tensile Strength psi	4,100 - 4,300	4,100 - 4,300	2, 700 - 2,900	4,100 - 4,300	2,500 - 2,700	2,500 - 2,700	1,900 - 2,100	3,400 - 3,600
Tensile Elongation %	20 - 30%	20 - 30%	30 - 40%	20 - 30%	40 - 50%	40 - 50%	20 - 30%	25 35%
Peel Strength pli	30	30	45	45	40	40	40	40
Tensile Lap Shear @ 77F	4,100- - 4,300	4,100- 4,300	3,700- 4,000	4,000- 4,200	3,700- 3,900	4,200- 4,400	3,900- 4,100	4,500- 4,700
Tensile Lap Shear @ 180F	1,900- 2,100	1,900- 2,100	2,700- 2,900	2,300- 2,500	1,900- 2,100	1,900- 2,100	1,600 1,800	2,800 3,000

	Description
	H3000 General Purpose, low-med viscosity, ideal for static joints. H3300 General Purpose, non-sag gel ideal for static joints. H4000 Fast setting, semi-flexible composite bonder, superior fatigue resistance. H4100 Rapid curing, non-sag gel, fatigue applications. H4200 Medium setting, flexible, General Purpose, low-med viscosity. H4300 Non-sagging gel, General Purpose, medium setting, flexible. H4400 Low viscosity, self leveling, rapid curing, General Purpose. H4800 Long open time, semi-flexible, composites bonder, fatigue applications.

 ARALDITE 2000 METHACRYLATES

METHACRYLATES Fast setting  & resilient for composites, thermoplastics, metals.
Araldite® 2021 Translucent/Yellow. Multi-purpose with rapid cure.High Toughness with ability to bond different substrates. Good for gap filling and verical applications.