Hysol ® H6000       Email
Methacrylate Adhesive
Description
Dexter Hysol H6000 is a sag-resistant, white, 10:1 methacrylate adhesive designed specifically for secondary bonding of gelcoats. This bright white adhesive retains its color after prolonged UV light exposure making it ideal for visible bonding areas. It also bonds to a variety of plastics such as FRP, PVC, and ABS with minimum surface preparation.

Recommended Substrates: Gelcoated FRP, many plastics and metals (Always use Hysol Primer 2000 when bonding metals such as aluminum , steel or stainless steel to improve long term durability.)

Features
Superior UV Resistance                                                          Superior impact and peel strength
Sag resistant/gaps filled to 1/2 inch                                      Rapid room temperature cure
Offers excellent tolerance to off-ratio mixing                    Non-yellowing bright white 100% reactive
Excellent environmental resistance                   

Typical Cured Properties
Tensile Strength, psi                            1,100 – 1,300                         ASTM D 638
Tensile Elongation, %                         45 - 55                                   ASTM D 638
Young's Modulus, psi                          87,000                                   ASTM D 638
Shore D Hardness                                 60 – 80

Typical Uncured Properties
                                                                     Part A                        Part B                       Mixed
Open Time @ 77°F                                  -                                    -                                15 - 25 minutes
Fixture Time @ 77°F                               -                                    -                                40 - 60 minutes
Peak Exotherm Temp, °F                       -                                    -                                250
Bondline Thickness, inches                                                                                          0.030 – 0.5
Color                                                          White                          White                      White
Viscosity, cps                                            80,000 – 120,000          30,000 – 60,000        -
Specific Gravity                                       1.02                               1.69                          1.10
Pounds/gallon                                          8.50                               14.9                          9.17
Mix Ratio by volume                              10                                   1                               -

Performance
The following table shows typical results for tensile lap shear (TLS)  per ASTM D1002 and side impact testing using GM9751P side impact tester. All testing done at 77ºF unless otherwise stated. Bondline thickness for all tests is 30 mils.

Substrate                                                                TLS, psi                               Impact, J/cm2
Plastics
Typical Marine Gel-coat                                               750                                                   1.35
ABS (GE Cycolac®)                                                     550                                                   0.77
PVC                                                                               700                                                   0.35
FRP                                                                                975                                                   0.70
FRP @ 180ºF                                                                 350                                                     -

Metals (All with Hysol Primer 2000)
Aluminum                                                                     1300                                                  0.28
Stainless Steel                                                                 1330                                                   -
Ground Cold Rolled Steel                                            1350                                                  0.46

Handling and Application
Mixing: It is highly recommended that either meter mix equipment or cartridges with static mix nozzles be used
to properly ratio and dispense the adhesive.  For hand mixing, combine Part A and Part B in the correct ratio
and mix thoroughly. This is important!  Heat buildup during and after mixing is normal.  To reduce the likelihood of exothermic reaction or excessive heat buildup, mix  less than 100 grams at a time.  Mixing smaller amounts will minimize heat buildup.

Applying: Bonding surfaces should be clean, dry, and free of contamination.  Extensive surface preparation is not required for H6000, and good bonds can be formed on most substrates after a solvent wipe.  To assure maximum bond strength, surfaces must be mated within the adhesive's open time.  Bondline thickness should be at least 30 mils. Use enough material to completely fill the joint when parts are clamped.

Curing: Parts should remain undisturbed during the interval of time between the material's open time and
fixture time.  After the fixture time is achieved the material has reached handling strength.  Temperature below
55°F will slow the cure; above 85°F will accelerate cure rate.

Clean Up: It is important to clean up excess adhesive from the work area and application equipment before it
cures.  Denatured alcohol and many common industrial solvents are suitable for removing uncured adhesive.  
Hysol H6000 is flammable.  Keep containers tightly closed after use.  Keep away from heat, sparks, and open
flames.

Storage: Hysol adhesives should be stored in a cool, dry place when not used for a long period of time. The shelf life for H6000 is one year from date of manufacture when stored at 40°F and six months when stored at 77°F.  Exposure above room temperature will reduce shelf life.

Packaging
100 gram clip packs       490ml EPS cartridges      

Technical Consultation Service
Our technical staff is ready to assist you in solving any special bonding requirements.  You are invited to take advantage of our extensive experience, laboratory services, and trained field service staff.  Call (800) 767 - 8786 now and let us help you with your adhesive needs.

DISCLAIMER: The information supplied in this document is for guidance only and should not be construed as a warranty.  All implied warranties are expressly disclaimed.  Including without limitation any warranty of merchantability and fitness for use: All users of the materials are responsible for assuring that it is suitable for their needs, environment and use.  All data is subject to change as Dexter deems appropriate.

Users should review the Material Safety Data Sheet (MSDS) and product label for the material to determine possible health hazards, appropriate engineering controls and precautions to be observed in using the material.  Copies of the MSDS and label are available upon request.

For more information or to order contact the Glu Guru™ at 1-800-323-5158
or Email mike@on-hand.com