Adhesives        
Acrylics
Aerosols
Anaerobics
Cyanoacrylates
Epoxies
Glue Dots
Hot Melt Adhesives
Methacrylates
Mold Releases
Sealants
Silicones
Solvent-Free
Structural Adhesives
Urethanes
UV Adhesives

   Applicators         
Accessories
Dispensers
Dual Dispensing
Epoxy
Hot Melt Dispensers
Hot Melt Bulk
Hot Melt Hoses
Hot Melt Rolls
Hot Melt Parts Nozzles/Parts
Motionless Mixers
Robots
Structural

Demonstrations

Bar Code Printer
Box Printer

Equipment
Drum Unloader
Slot Die Applicator
Cold Glue Applicator
Fiberized Spray Pattern Controllers
Bulk Meters
Drum Meters
Adhesive Feeders
Metering Station
Supply Units
   
   Applications       
Carton Sealing
Electronic Materials
Encapsulants
Green Adhesives
Magnet Bonding
Marine Adhesives
Medical Device
One Part Adhesives
Packaging
Potting
Robotic
Solvent-Free Spray
Space Age Adhesive
Surfacing Adhesives
Transportation
Woodworking

Literature                
About Bonding
Data Sheets
Journals
Line Card
MSDS
Tech Menu

      
Meeting Customer expectations
and requirements is the main objective
 of   ISO 9001:2008
 

Customer Survey
 We would appreciate your help so that we can provide you with the very best in services. Your response will help us address the areas of performance needing improvement.

Hysol ®9436 
You may print this page for your file
Epoxy Adhesive 

Description
Hysol 9436 is an unfilled two part room temperature curing epoxy adhesive with excellent strength retention at elevated temperatures. It consists of a liquid resin and curing agent. Hysol 9436 yields rigid bonds that are resistant to salt spray and humidity exposure. This adhesive can also be used for laminating and for potting small assemblies.

Features
Excellent Tensile Sheer Strength                              High Temperature Resistant
Outstanding Environmental Resistance                 Low Viscosity - pourable
Room Temperature Curing

Typical Properties
                                                        Part A                                       Part B                                            Mixed
Color                                               Amber                                     Green                                             Pale Green
Viscosity, cps,                                 40,000                                       1000-3000                                     11,000
Brookfield HBT (Spdl)                 4 @ 20 rpm                              1 @ 20 rpm                                  3 @ 20 rpm
Specific Gravity                               1.22                                           0.95                                               1.10
Pounds per gallon                         10.5                                            8.0                                                 9.2

Handling
Mixing: This product requires mixing two components together just prior to the application. Complete mixing is necessary. The temperature of the separate components prior to mixing is not critical, but they should be at room temperature.
                                                                Part A                                           Part B
By weight                                                  100                                                 58  
By volume                                                 43                                                    -
Pot life, (250 grams)                                                  45 minutes
Peak Exotherm, (250 grams)                                    525 @ 55°F

Application
Mixing – Bulk: Combine Part A (resin) and Part B (hardener) in the correct ratio and mix thoroughly. This is important! Heat build-up during or after mixing is normal. Do not mix quantities greater than two pounds as dangerous heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.

Application: Bonding surfaces should be clean and dry. For optimum surface preparation, consult Dexter's bulletin "Preparing the Surface for Adhesive Bonding". Once the adhesive is applied, the boned parts should beheld in contact until the part has developed handling strength. It is not necessary to clamp the parts unless movement during curing is likely.

Cure: Hysol 9436 can be cured for 5 days at room temperature. Curing temperatures up to 200°F can be used to reduce cure time. For example, 1 hour at 180°F will give complete cure.

Clean up: It is important to remove excess adhesive from the work area and application equipment before it hardens. Many  common solvents and citrus cleaners are suitable for removing uncured adhesive. Consult with your supplier's information pertaining to the safe and proper use of solvents.

Performance
Tensile Lap Shear Strength: (tested per ASTM D1002 after curing for five days at 75oF on 1 x 0.5 overlap specimens)
Substrate                                                Test Temperature oF                             Tensile Lap Sheer Strength, psi
Etched Aluminum                                                77                                                                  2100
                                                                              -67                                                                  1800
                                                                               180                                                                1850
                                                                               300                                                                 900                               Degreased Aluminum                                          77                                                                   900  
FRP (1" overlap)                                                    77                                                                   900
Graphite-Epoxy Laminate                                    77                                                                   3300
Etched Aluminum after
Environmental Exposure:
30 day salt spray                                                     77                                                                   1950
30 day 120°F, @ 100%                                          77                                                                   1600
relative humidity
7 day @ 77°F hydraulic oil                                     77                                                                   3000

Bulk Properties
Tensile properties tested at room temperature on 0.125-inch castings per ASTM D 638.
Tensile Strength, psi                                                  5,900
Tensile Modulus, psi                                                 370,000
Elongation at break, %                                              2.4
Shore D hardness                                                     80

Technical Consultation Service
Our technical staff and representative are ready to assist in solving any special bonding requirements. You are invited to take advantage of our extensive experience, laboratory services and trained field service staff. Call 800.767.8786 now and let us help you with your adhesive needs.